Converters

Approx. Rs 3,500 / Piece Get Latest Price

RS232 to RS485 Converter ,RS232 to RS422 Converter ,
RS422/RS485 Repeater;3000V optic-electric isolation.

Industrial Isolation RS232 to RS485 Converter and RS422/RS485 Repeater(SW485GI)

Features

1. Support DIN-rail, Terminal block connection

2. 12~36VDC Power input(3 bit terminal block)

3. Adopt itself adapt interface technique, no use for setup switch

4. Adopt ADDC, auto distinguish and data transfer direction.

5. Can use for RS485/422 repeater and RS232 to RS485/422 converter, but just use

one function at same time

6. Supply 3000V optic-electric isolation, 1500W surge protection

7. Reach up to 3000m at the rate of 9600bps

Introduction

SW485GI Can use for RS485/422 repeater and RS232 to RS485/422 converter, but just use one function at same time. The product must have 12-36VDC power input, optic- electrical isolation more than 3KV. Have small volume, 3000m transfer distance, high rate, steadily performance and so on. It is abroad used in industry control system, It is a best performance and price interface converter and Repeater.

Specification

Standards: EIA RS-232C, RS-485, RS422 standard

RS-232 signal: TX, RX, GND

RS-422 signal: T+, T-, R+, R-, GND

RS-485 signal: D+, D-, GND

Working mode: Asynchronism, point to point or multi point, 2 wire half-duplex,4 wire full duplex

Baud rate: 300~115200bps, auto test serial signal rate detect signal speed automatically, zero delay time

Flow control: Data direction auto-turnaround, no flow control is required

Transfer distance: RS-485/422 side:3Km(9600bps)

RS-232 side: no less than 5m

Max number of drops: 128 nodes

Optical isolation: 3000V

Port protect: 1500W surge protection,15KV ESD protection

Connector: RS-232 side DB9 female

RS-485/422 side 5 bit terminal block

Isolation mode, adopt +12V~36VDC input power, provide 3000V isolation

Environment

Operating temperature: -10°C to 60°C

Storage temperature: -40°C to 85°C

Humidity: 5% to 95%(no condensation)

Appearance

Dimensions: 100.0mm×69.0mm×22.0mm

Material: Iron(shell)

Approx. Rs 3,500 / Piece Get Latest Price

RS232 to RS485 Converter ,RS232 to RS422 Converter ,
RS422/RS485 Repeater;3000V optic-electric isolation.

Industrial Isolation RS232 to RS485 Converter and RS422/RS485 Repeater(SW485GI)

Features

1. Support DIN-rail, Terminal block connection

2. 12~36VDC Power input(3 bit terminal block)

3. Adopt itself adapt interface technique, no use for setup switch

4. Adopt ADDC, auto distinguish and data transfer direction.

5. Can use for RS485/422 repeater and RS232 to RS485/422 converter, but just use

one function at same time

6. Supply 3000V optic-electric isolation, 1500W surge protection

7. Reach up to 3000m at the rate of 9600bp

Introduction

 

SW485GI Can use for RS485/422 repeater and RS232 to RS485/422 converter, but just use one function at same time. The product must have 12-36VDC power input, optic- electrical isolation more than 3KV. Have small volume, 3000m transfer distance, high rate, steadily performance and so on. It is abroad used in industry control system, It is a best performance and price interface converter and Repeater.

 

 

Specification

 

Standards: EIA RS-232C, RS-485, RS422 standard

RS-232 signal: TX, RX, GND

RS-422 signal: T+, T-, R+, R-, GND

RS-485 signal: D+, D-, GND

Working mode: Asynchronism, point to point or multi point, 2 wire half-duplex,4 wire full duplex

Baud rate: 300~115200bps, auto test serial signal rate detect signal speed automatically, zero delay time

Flow control: Data direction auto-turnaround, no flow control is required

Transfer distance: RS-485/422 side:3Km(9600bps)

RS-232 side: no less than 5m

Max number of drops: 128 nodes

Optical isolation: 3000V

Port protect: 1500W surge protection,15KV ESD protection

Connector: RS-232 side DB9 female

RS-485/422 side 5 bit terminal block

Isolation mode, adopt +12V~36VDC input power, provide 3000V isolation

Environment

Operating temperature: -10°C to 60°C

Storage temperature: -40°C to 85°C

Humidity: 5% to 95%(no condensation)

Appearance

Dimensions: 100.0mm×69.0mm×22.0mm

Material: Iron(shell)

Color: White 

Approx. Rs 3,500 / Piece Get Latest Price

Industrial Isolation RS232 to RS485 Converter and RS422/RS485 Repeater(SW485GI)

Features

1. Support DIN-rail, Terminal block connection

2. 12~36VDC Power input(3 bit terminal block)

3. Adopt itself adapt interface technique, no use for setup switch

4. Adopt ADDC, auto distinguish and data transfer direction.

5. Can use for RS485/422 repeater and RS232 to RS485/422 converter, but just use

one function at same time

6. Supply 3000V optic-electric isolation, 1500W surge protection

7. Reach up to 3000m at the rate of 9600bp

Introduction

 

SW485GI Can use for RS485/422 repeater and RS232 to RS485/422 converter, but just use one function at same time. The product must have 12-36VDC power input, optic- electrical isolation more than 3KV. Have small volume, 3000m transfer distance, high rate, steadily performance and so on. It is abroad used in industry control system, It is a best performance and price interface converter and Repeater.

 

 

Specification

 

Standards: EIA RS-232C, RS-485, RS422 standard

RS-232 signal: TX, RX, GND

RS-422 signal: T+, T-, R+, R-, GND

RS-485 signal: D+, D-, GND

Working mode: Asynchronism, point to point or multi point, 2 wire half-duplex,4 wire full duplex

Baud rate: 300~115200bps, auto test serial signal rate detect signal speed automatically, zero delay time

Flow control: Data direction auto-turnaround, no flow control is required

Transfer distance: RS-485/422 side:3Km(9600bps)

RS-232 side: no less than 5m

Max number of drops: 128 nodes

Optical isolation: 3000V

Port protect: 1500W surge protection,15KV ESD protection

Connector: RS-232 side DB9 female

RS-485/422 side 5 bit terminal block

Isolation mode, adopt +12V~36VDC input power, provide 3000V isolation

Environment

Operating temperature: -10°C to 60°C

Storage temperature: -40°C to 85°C

Humidity: 5% to 95%(no condensation)

Appearance

Dimensions: 100.0mm×69.0mm×22.0mm

Material: Iron(shell)

Color: White 

Approx. Rs 3,500 / Piece Get Latest Price

Model : SW485CThe SW485C is an industrial grade bi-directional port-powered RS-232 to RS-485 or RS-422 converter in a 9 pin format. It can convert any standard full duplex RS-232 port to any two-wire balanced half duplex RS-485 port or four-wire balanced full duplex RS-485 or RS-422 port. In simple terms, it will convert any RS-232 signal to a RS-485 or RS-422 signal and vice versa. The unit is powered from the RS-232 data lines. It also supports data direction auto-turnaround. Therefore, no external power or flow control is required. The data direction auto-turnaround automatically enables the RS-485/422 driver when data is present on the RS-232 side making the device plug-and-play, requiring no software drivers. The SW485C has a DB9 female connector on the RS-232 side and either a DB9 male connector or 5 bit terminal block on the RS-485/422 side.

Features1. Plug-and-Play, small volume, easy installation 
2. Port-powered, high efficiency obtain electricity, can also worked on 3 lines
3. RS-232 to RS-485 or RS-232 to RS-422
4. Lowest consumption
5. Automatic send data control, auto distinguish and sense direction adopt data transfer
6. Auto sense serial signal rate, zero delay automatic transmit Specification

Standards: EIA RS-232C, RS-485,RS-422 standard
RS-232 signal: TX, RX, GND
RS-422 signal: T+, T-, R+, R-, GND
RS-485 signal: D+, D-, GND
Working mode: Asynchronism, point to point or multi point, 2 wire half-duplex,4 wire full duplex
Baud rate: 300~115200bps, auto test serial signal rate detect signal speed automatically, zero delay time
Flow control: Data direction auto-turnaround, no flow control is required
Transfer distance: RS-485/422 side:1.2Km,115200bps
RS-232 side: no less than 5m
Max number of drops: 128 nodes
Optical isolation: 2500V
Port protect: 1500W surge protection,15KV ESD protection
Connector: RS-232 side DB9 female
                 RS-485/422 side DB9M( DB9F to 5 bit terminal block)
Power
Power input: No power supply need, powered from TXD, RTS,DTR
Consumption: Static less than 10mA, dynamic less than 40mA
Environment
Operating temperature: -20°C to 60°C 
Storage temperature: -40°C to 85°C
Humidity: 5% to 95%(no condensation)
Appearance
Dimensions: 95.0mm×33.0mm×16.5mm      
Material: Plastic(shell) 
Weight: 50g

Approx. Rs 3,500 / Piece Get Latest Price

Model : SW485WAThe SW485WA is an industrial grade bi-directional port-powered 2500V opto-isolated RS232 to RS485 converter in a 9 pin format. It can convert any standard full duplex RS232C port to any two-wire balanced half duplex RS485 port. In simple terms, it will convert any RS232 signal to a RS485 signal and vice versa. The unit is powered from the RS232 data lines. It also supports data direction auto-turnaround. Therefore, no external power or flow control is required. The data direction auto-turnaround automatically enables the RS485 driver when data is present on the RS232 side making the device plug-and-play, requiring no software drivers. The SW485WA has a DB9 female connector on the RS232 side and either a DB9 male connector or 3 bit terminal block on the RS485 side.

Features1. Optical isolation effectively protects RS-232/RS-485 devices from transient surges, ground loop, and remote lightning
2. Plug-and-Play (Device is hot-pluggable, Data format Auto-sensing & Self-adjusting)
3. Maximum baud rate 38400bps, 1200m(9600bps)
4. Port-powered, no external power or TXD, RTS, DTR required
5. Data direction auto-turnaround, no flow control is required
6. 2500V isolation, no power supply needed

Specification

Standards: EIA RS-232C, RS-485 standard
RS-232 signal: TX, RX, GND
RS-485 signal: D+, D-, GND
Working mode: Asynchronism, point to point or multi point, 2 wire half-duplex
Baud rate: 300~115200bps, auto test serial signal rate detect signal speed automatically, zero delay time
Flow control: Data direction auto-turnaround, no flow control is required
Transfer distance: RS-485 side: 1.2Km, 9600bps
RS-232 side: no less than 5m
Max number of drops: 128 nodes
Optical isolation: 2500V
Port protect: 1500W surge protection, 15KV ESD protection
Connector: RS-232 side DB9 female
                 RS-485 side DB9M( DB9F to 3 bit terminal block)
Power
Power input: No power supply need, powered from TXD, RTS,DTR
Consumption: Static less than 10mA, dynamic less than 40mA
Environment
Operating temperature: -20°C to 60°C 
Storage temperature: -40°C to 85°C
Humidity: 5% to 95%(no condensation)
Appearance
Dimensions: 95.0mm×33.0mm×16.5mm      
Material: Plastic(shell) 

Weight: 50g

Approx. Rs 3,500 / Piece Get Latest Price

SW4485I-P(12/48VDC) is RS-485 HUB is designed for RS-485 system in complicated electromagnetic environment. It supports a transmission rate up to 115.2KBPS, and adopts two-way transparent transmission, which allows one RS-485 bus or one RS-232 bus to be divided into 4 RS-485 buses, or any divided RS-485 signal to be transparently transmitted to host computer RS-485 or RS-232 hub. Each RS-485 port of slave computer is provided with reverse connection alarm and protection function, with which the reliability of existing RS-485 network is greatly improved, effectively reducing the network maintenance time. To ensure the security and reliability of data communication, the RS-485 ports are provided with 2KVAC isolation protection, level-4 electrostatic protection and level-2 radiated susceptibility, effectively preventing surge current, common ground and radiated interference, making the hub safe and reliable and suitable for outdoor application.
SW4485I-P(12/48VDC) also comes with RS-485 bus star connection. Users can easily improve RS-485 bus structure and divide the network segment. Proper utilization of SW4485I-P(12/48VDC) can help design a unique and reliable RS-485 system. SW4485I-P(12/48VDC) adopts EMC protection and supports DIN-rail installation, allowing it to be used reliably in severe environment at a temperature of -40~85.

FeaturesSupport two host computer RS-232 and RS-485 ports and four slave computer RS-485 portsSupport transmission rate 300~115200bpsSupport multiple SW4485I-P(12/48VDC) cascade connection as many as 256-way RS-485 busEach slave computer port can connect 32 standard RS-485 devices (nodes)Special automatic reverse connection alarmZero-delay automatic send/receive conversion functionPort is provided with 2KVAC isolation protection,Level-4 electrostatic protection and level-2 radiated susceptibilityIndustrial design, IP40 protectionSupport DIN-rail installationWorking temperature -4085Specification

Communication Parameters

Interface Protocol compliant with EIARS-232/48 5

Serial port number 1 host computer RS-232 port, 1 host computer RS-485 port, 4 slave computer RS-485 ports

RS-232 signal TxD, RxD, GND

RS-485 signal D+, D-, GND

Parity bit None, Even, Odd, Space, Mark

Data bit 5bit, 6bit, 7bit, 8bit

Stop bit 1bit, 1.5bit, 2bit

Baud rate 300bps~115200bps

Direction control RS-485 adopts ADDC technology

Transmission media CAT.5E shielded twisted pair or dedicated line for RS-485

Load capacity support 32 nodes (customizable to 128 nodes) polling

Port protection 2KVAC isolation protection, level-4 electrostatic protection, level-2 radiated susceptibility

Transmission distance RS-485 1200m, RS-232 is less than 15m

Connector

Host computer RS-232/485 5PIN terminal blocks

Slave computer RS-485 10PIN terminal blocks

Indicator

PWR power indicator

TXD data sending status indicator

RXD data receiving status indicator

E1~E4 slave computer RS-485 port status indicator

Power

Input voltage 12-48VDC

No-load power 0.696W@24VDC

Full-load power 0.696W@24VDC

Mechanical structure

Shell IP40 protection, high-strength metal shell

Installation DIN-rail installation

Weight 384.8g

Dimension (L*W*H) 110mm*95mm*35mm

Working environment

Working temperature -40~85

Storage temperature -40~85

Humidity 5%~95% (no condensation)

Industry standard

EMI FCC Part 15, CISPR (EN55022) class A

EMS EN61000-4-2 (ESD), Level 4

EN61000-4-3 (RS), Level 2

Shock IEC 60068-2-27

Free fall IEC 60068-2-32

Vibration test IEC 60068-2-6

Approx. Rs 3,500 / Piece Get Latest Price

Model : SW485CThe SW485C is an industrial grade bi-directional port-powered RS-232 to RS-485 or RS-422 converter in a 9 pin format. It can convert any standard full duplex RS-232 port to any two-wire balanced half duplex RS-485 port or four-wire balanced full duplex RS-485 or RS-422 port. In simple terms, it will convert any RS-232 signal to a RS-485 or RS-422 signal and vice versa. The unit is powered from the RS-232 data lines. It also supports data direction auto-turnaround. Therefore, no external power or flow control is required. The data direction auto-turnaround automatically enables the RS-485/422 driver when data is present on the RS-232 side making the device plug-and-play, requiring no software drivers. The SW485C has a DB9 female connector on the RS-232 side and either a DB9 male connector or 5 bit terminal block on the RS-485/422 side.

Features1. Plug-and-Play, small volume, easy installation
2. Port-powered, high efficiency obtain electricity, can also worked on 3 lines
3. RS-232 to RS-485 or RS-232 to RS-422
4. Lowest consumption
5. Automatic send data control, auto distinguish and sense direction adopt data transfer
6. Auto sense serial signal rate, zero delay automatic transmit Specification

Standards: EIA RS-232C, RS-485,RS-422 standard
RS-232 signal: TX, RX, GND
RS-422 signal: T+, T-, R+, R-, GND
RS-485 signal: D+, D-, GND
Working mode: Asynchronism, point to point or multi point, 2 wire half-duplex,4 wire full duplex
Baud rate: 300~115200bps, auto test serial signal rate detect signal speed automatically, zero delay time
Flow control: Data direction auto-turnaround, no flow control is required
Transfer distance: RS-485/422 side:1.2Km,115200bps
RS-232 side: no less than 5m
Max number of drops: 128 nodes
Optical isolation: 2500V
Port protect: 1500W surge protection,15KV ESD protection
Connector: RS-232 side DB9 female
RS-485/422 side DB9M( DB9F to 5 bit terminal block)

Approx. Rs 3,500 / Piece Get Latest Price

The SW485C is an industrial grade bi-directional port-powered RS-232 to RS-485 or RS-422 converter in a 9 pin format. It can convert any standard full duplex RS-232 port to any two-wire balanced half duplex RS-485 port or four-wire balanced full duplex RS-485 or RS-422 port. In simple terms, it will convert any RS-232 signal to a RS-485 or RS-422 signal and vice versa. The unit is powered from the RS-232 data lines. It also supports data direction auto-turnaround. Therefore, no external power or flow control is required. The data direction auto-turnaround automatically enables the RS-485/422 driver when data is present on the RS-232 side making the device plug-and-play, requiring no software drivers. The SW485C has a DB9 female connector on the RS-232 side and either a DB9 male connector or 5 bit terminal block on the RS-485/422 side.

Features1. Plug-and-Play, small volume, easy installation 
2. Port-powered, high efficiency obtain electricity, can also worked on 3 lines
3. RS-232 to RS-485 or RS-232 to RS-422
4. Lowest consumption
5. Automatic send data control, auto distinguish and sense direction adopt data transfer
6. Auto sense serial signal rate, zero delay automatic transmit

Specification

Standards: EIA RS-232C, RS-485,RS-422 standard
RS-232 signal: TX, RX, GND
RS-422 signal: T+, T-, R+, R-, GND
RS-485 signal: D+, D-, GND
Working mode: Asynchronism, point to point or multi point, 2 wire half-duplex,4 wire full duplex
Baud rate: 300~115200bps, auto test serial signal rate detect signal speed automatically, zero delay time
Flow control: Data direction auto-turnaround, no flow control is required
Transfer distance: RS-485/422 side:1.2Km,115200bps
RS-232 side: no less than 5m
Max number of drops: 128 nodes
Optical isolation: 2500V
Port protect: 1500W surge protection,15KV ESD protection
Connector: RS-232 side DB9 female
                 RS-485/422 side DB9M( DB9F to 5 bit terminal block)
Power
Power input: No power supply need, powered from TXD, RTS,DTR
Consumption: Static less than 10mA, dynamic less than 40mA
Environment
Operating temperature: -20°C to 60°C 
Storage temperature: -40°C to 85°C
Humidity: 5% to 95%(no condensation)
Appearance
Dimensions: 95.0mm×33.0mm×16.5mm      

Material: Plastic(shell)

Approx. Rs 7,000 / Piece Get Latest Price

MC201 is a CAN bus to fiber converter. It designs specially to deal with the short transmission distance of CAN bus, the subjection to electromagnetic interference and other issues. CAN bus transfer to fiber is able to provide the user with transparent data transmission of CAN bus to fiber. It is working in pairs, is more convenient to put the CAN signal revert to the CAN signal through fiber transmission.
MC201 serial converter integrates an optical interface and a 2KVAC electrically isolated CAN bus interface, is able to receive/store/transmit different rates between 2 CAN network data. CAN bus interface of MC201 supports various of standard communication baud rate recommended by CiA, is capable for detecting and matching automatical baud rate and defining baud rate by user, the baud rate ranges from 2.5Kbps to 1Mbps; it can connect external termination resistors at the same time.Its single-model fiber interface can be used in high-interference environment and has concentrated energy , which is more suitable for long-distance transmission , is better to extend the network communication distance.
MC201 adopts EMC protection design, supports wall and panel mounting. It can be used at the harsh environment from -40℃ to 85℃.

SpecificationFiber Interface
Interface Type: single optical port or dual optical port, SC/ST/FC optional
Fiber Type: single-model/multi-model
Wavelength: 1310nm
CAN Interface
Standard: CAN2.0A, CAN2.0B
CAN Signal: GND, CANL, CANH
Baud Rate: 2.5K ~ 1000K bps
Interface Resistor: 120ohm external Terminator optional
Port Node: load capacity supports 110 nodes
Interface Protection: 2KVAC isolation protection, 8KV ESD protection(air discharge)
Interface Type: 5PIN terminals
Transmit Distance
CAN Interface: 40m~10Km
Single-model Fiber: 0~15Km
Indicator
CAN:CAN channel status indicator
LOS: Network error status indicator
Power: Power indicator
Power
Input Voltage: 5VDC
No-load Power: 1.385W@5VDC
Full Power:1.310W@5VDC
Mechanical Structure
Shell???IP40 protection grade, high-strength metal casing
Installation: Wall-mount and Panel-mount
Weight: 237g
Size(H*W*L): 22mm×69mm×10mm
Working Environment
Working Temperature: -40~85℃
Storage Temperature: -40~85℃
Industry Standard
EMI: FCC Part 15, CISPR(EN55022) class A
EMS: EN61000-4-2(ESD), Lece3
Shock: IEC60068-2-27
Free Fall: IEC60068-2-32
Shake: IEC60068-2-6

Approx. Rs 5,400 / Piece Get Latest Price

Model : NP301NP301 serial device server is designed to make your serial devices internet ready instantly. It provides 1 port RS232/485/422 (RS232, DB9M; RS485/422, 5 bit terminal block) and 1 port 10/100Base-T(X).It makes them ideal choice for connecting decentral serial devices and Host computer to an IP based Ethernet, making it easily and conviniently for your management. Its software can be setting and updating by serial program group in the application. It supports TCP, UDP, ARP, ICMP, DHCP and Windows Native COM, LLF functions.

Features

1.Adopt 32 bit ARM processor
2.Support 3-in-1 RS-232/RS-485/RS-422 serial interface
3.Support 10/100M
4.Support 300bps-115.2Kbps
5.Support TCP, UDP, ARP, ICMP, HTTP and DHCP protocol
6.Support across gateway, router communication
7.Support standard TCP/IP SOCKET
8.Support Windows serial interface driver mode
9.Support Virtual serial driver access and auto connect once the network disconnect
10.Support network and serial interface configuration mode
11.Low consumption design
12.Support DIN-Rail or wall mounting installation
13.Working termperature: -40～75℃

 Specification

LAN：
Standard: 10Base-T，100Base-TX
Protocol: Support  TCP, UDP, APR, ICMP and DHCP protocol
Signal: Rx+,Rx-,Tx+,Tx-
Speed: 10/100Mbps
Working: Full-duplex and half-duplex
Working mode: Support Server and Client
Transmission; 100m
Connector: RJ45

Serial interface:
Serial interface number: 1 port RS-232,1 port RS-422/485
RS-232 signal: TXD,RXD,RTS,CTS,DTR,DSR,GND 
RS-422 signal: T+（A）,T-(B),R+(A),R-(B),GND
RS-485 signal: D+（A）,D-(B),GND
Parity bit: None,Even,Odd,Space,Mark
Data bit: 5bit,6bit,7bit,8bit
Baud rate: 300bps～115200bps
Flow control: RTS/CTS or XON/XOFF
Direction control: RS485 side adopt ADDC technology, auto text and control data transfer direction
Loading: RS-485/422 side support 32 nodes (customize 128 nodes) loopback
Transmission: RS-485/422 side 1200m; RS-232 side 15m
Interface protection: 1500W surge protection, 15KV static protection
Interface type: RS-232 side DB9 male，RS-485/422 side 5 bit terminal block

Approx. Rs 5,400 / Piece Get Latest Price

Model : NP301NP301 serial device server is designed to make your serial devices internet ready instantly. It provides 1 port RS232/485/422 (RS232, DB9M; RS485/422, 5 bit terminal block) and 1 port 10/100Base-T(X).It makes them ideal choice for connecting decentral serial devices and Host computer to an IP based Ethernet, making it easily and conviniently for your management. Its software can be setting and updating by serial program group in the application. It supports TCP, UDP, ARP, ICMP, DHCP and Windows Native COM, LLF functions.

Features

1.Adopt 32 bit ARM processor
2.Support 3-in-1 RS-232/RS-485/RS-422 serial interface
3.Support 10/100M
4.Support 300bps-115.2Kbps
5.Support TCP, UDP, ARP, ICMP, HTTP and DHCP protocol
6.Support across gateway, router communication
7.Support standard TCP/IP SOCKET
8.Support Windows serial interface driver mode
9.Support Virtual serial driver access and auto connect once the network disconnect
10.Support network and serial interface configuration mode
11.Low consumption design
12.Support DIN-Rail or wall mounting installation
13.Working termperature: -40～75℃

 Specification

LAN：
Standard: 10Base-T，100Base-TX
Protocol: Support  TCP, UDP, APR, ICMP and DHCP protocol
Signal: Rx+,Rx-,Tx+,Tx-
Speed: 10/100Mbps
Working: Full-duplex and half-duplex
Working mode: Support Server and Client
Transmission; 100m
Connector: RJ45

Serial interface:
Serial interface number: 1 port RS-232,1 port RS-422/485
RS-232 signal: TXD,RXD,RTS,CTS,DTR,DSR,GND 
RS-422 signal: T+（A）,T-(B),R+(A),R-(B),GND
RS-485 signal: D+（A）,D-(B),GND
Parity bit: None,Even,Odd,Space,Mark
Data bit: 5bit,6bit,7bit,8bit
Baud rate: 300bps～115200bps
Flow control: RTS/CTS or XON/XOFF
Direction control: RS485 side adopt ADDC technology, auto text and control data transfer direction
Loading: RS-485/422 side support 32 nodes (customize 128 nodes) loopback
Transmission: RS-485/422 side 1200m; RS-232 side 15m
Interface protection: 1500W surge protection, 15KV static protection
Interface type: RS-232 side DB9 male，RS-485/422 side 5 bit terminal block

Power supply:
Power input: 12VDC(9~48VDC)
Consumption: Approx 1.4W

Approx. Rs 5,300 / Piece Get Latest Price

NP301 serial device server is designed to make your serial devices internet ready instantly. It provides 1 port RS232/485/422 (RS232, DB9M; RS485/422, 5 bit terminal block) and 1 port 10/100Base-T(X).It makes them ideal choice for connecting decentral serial devices and Host computer to an IP based Ethernet, making it easily and conviniently for your management. Its software can be setting and updating by serial program group in the application. It supports TCP, UDP, ARP, ICMP, DHCP and Windows Native COM, LLF functions.

Features

1.Adopt 32 bit ARM processor
2.Support 3-in-1 RS-232/RS-485/RS-422 serial interface
3.Support 10/100M
4.Support 300bps-115.2Kbps
5.Support TCP, UDP, ARP, ICMP, HTTP and DHCP protocol
6.Support across gateway, router communication
7.Support standard TCP/IP SOCKET
8.Support Windows serial interface driver mode
9.Support Virtual serial driver access and auto connect once the network disconnect
10.Support network and serial interface configuration mode
11.Low consumption design
12.Support DIN-Rail or wall mounting installation
13.Working termperature: -40～75℃

 Specification

LAN：
Standard: 10Base-T，100Base-TX
Protocol: Support  TCP, UDP, APR, ICMP and DHCP protocol
Signal: Rx+,Rx-,Tx+,Tx-
Speed: 10/100Mbps
Working: Full-duplex and half-duplex
Working mode: Support Server and Client
Transmission; 100m
Connector: RJ45

Serial interface:
Serial interface number: 1 port RS-232,1 port RS-422/485
RS-232 signal: TXD,RXD,RTS,CTS,DTR,DSR,GND 
RS-422 signal: T+（A）,T-(B),R+(A),R-(B),GND
RS-485 signal: D+（A）,D-(B),GND
Parity bit: None,Even,Odd,Space,Mark
Data bit: 5bit,6bit,7bit,8bit
Baud rate: 300bps～115200bps
Flow control: RTS/CTS or XON/XOFF
Direction control: RS485 side adopt ADDC technology, auto text and control data transfer direction
Loading: RS-485/422 side support 32 nodes (customize 128 nodes) loopback
Transmission: RS-485/422 side 1200m; RS-232 side 15m
Interface protection: 1500W surge protection, 15KV static protection
Interface type: RS-232 side DB9 male，RS-485/422 side 5 bit terminal block

Power supply:
Power input: 12VDC(9~48VDC)
Consumption: Approx 1.4W

Environment
Working temperature:-40°C～75°C
Storage temperature:-40°C～85°C
Humidity: Relative humidity 5% to 95%

Approx. Rs 9,500 / Piece Get Latest Price

NP302T-2D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 2 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-232 port
RS-232 port number: 2
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR, RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit: 1bit,1.5bit,2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 3 static
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS232 port data indicator: TX, RX
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:0.66W@12VDC
Full-load consumption: 0.67W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）

Approx. Rs 9,500 / Piece Get Latest Price

Model : NP302T-2D(RS-232)NP302T-2D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 2 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-232 port
RS-232 port number: 2
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR, RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit: 1bit,1.5bit,2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 3 static
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS232 port data indicator: TX, RX
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:0.66W@12VDC
Full-load consumption: 0.67W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）

Approx. Rs 9,500 / Piece Get Latest Price

NP302T-2D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 2 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-232 port
RS-232 port number: 2
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR, RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit: 1bit,1.5bit,2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 3 static
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS232 port data indicator: TX, RX
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:0.66W@12VDC
Full-load consumption: 0.67W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell: IP30 protection, metal shell
Installation: Wall mounting

Approx. Rs 9,500 / Piece Get Latest Price

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-232 port
RS-232 port number: 2
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR, RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit: 1bit,1.5bit,2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 3 static
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS232 port data indicator: TX, RX
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:0.66W@12VDC
Full-load consumption: 0.67W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）

Approx. Rs 10,200 / Piece Get Latest Price

Model NP302T-2D(RS-485)NP302T-2D(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 2 port RS-485/422(RS-485/422 connector 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature -4085℃

Specification

Ethernet port
Standard 10Base-T, 100Base-TX
Protocol Support TCP, UDP, APR, ICMP and DHCP
Signal Rx+, Rx-, Tx+, Tx-
Speed 10/100Mbps
Working Full-duplex and half duplex
Working mode Support TCP Server and Client
Transfer distance 100m
Connector RJ45
RS-485/422 port
RS-485 /422 port number 2
RS-485 signal D+, D-, GND
RS-422 signal T+, T-, GND, R+, R-
Parity bit None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit 1bit,1.5bit,2bit
Band rate 300bps115200bps
Loading support 32 nodes loop back
Transfer distance 1200m
Connector terminal block
Protection class 3 static, 1.5KV isolation
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS-485/422 port data indicator TX, RX
Power supply
Input voltage 12VDC(9~48VDC)
No-load consumption0.89W@12VDC
Full-load consumption 0.93W@12VDC
Environment limits
Working temperature -40~85℃
Storage temperature -40~85℃
Relative humidity 5%~95%non-condensing

Approx. Rs 10,500 / Piece Get Latest Price

Model NP302T-2D(RS-485)NP302T-2D(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 2 port RS-485/422(RS-485/422 connector 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature -4085℃

Specification

Ethernet port
Standard 10Base-T, 100Base-TX
Protocol Support TCP, UDP, APR, ICMP and DHCP
Signal Rx+, Rx-, Tx+, Tx-
Speed 10/100Mbps
Working Full-duplex and half duplex
Working mode Support TCP Server and Client
Transfer distance 100m
Connector RJ45
RS-485/422 port
RS-485 /422 port number 2
RS-485 signal D+, D-, GND
RS-422 signal T+, T-, GND, R+, R-
Parity bit None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit 1bit,1.5bit,2bit
Band rate 300bps115200bps
Loading support 32 nodes loop back
Transfer distance 1200m
Connector terminal block
Protection class 3 static, 1.5KV isolation
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS-485/422 port data indicator TX, RX
Power supply
Input voltage 12VDC(9~48VDC)
No-load consumption0.89W@12VDC
Full-load consumption 0.93W@12VDC
Environment limits
Working temperature -40~85℃
Storage temperature -40~85℃
Relative humidity 5%~95%non-condensing

Approx. Rs 10,500 / Piece Get Latest Price

NP302T-2D(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 2 port RS-485/422(RS-485/422 connector 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature -4085℃

Specification

Ethernet port
Standard 10Base-T, 100Base-TX
Protocol Support TCP, UDP, APR, ICMP and DHCP
Signal Rx+, Rx-, Tx+, Tx-
Speed 10/100Mbps
Working Full-duplex and half duplex
Working mode Support TCP Server and Client
Transfer distance 100m
Connector RJ45
RS-485/422 port
RS-485 /422 port number 2
RS-485 signal D+, D-, GND
RS-422 signal T+, T-, GND, R+, R-
Parity bit None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit 1bit,1.5bit,2bit
Band rate 300bps115200bps
Loading support 32 nodes loop back
Transfer distance 1200m
Connector terminal block
Protection class 3 static, 1.5KV isolation
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS-485/422 port data indicator TX, RX
Power supply
Input voltage 12VDC(9~48VDC)
No-load consumption0.89W@12VDC
Full-load consumption 0.93W@12VDC
Environment limits
Working temperature -40~85℃
Storage temperature -40~85℃
Relative humidity 5%~95%non-condensing

Approx. Rs 10,300 / Piece Get Latest Price

Model NP302T-2D(RS-485)NP302T-2D(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 2 port RS-485/422(RS-485/422 connector 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature -4085℃

Specification

Ethernet port
Standard 10Base-T, 100Base-TX
Protocol Support TCP, UDP, APR, ICMP and DHCP
Signal Rx+, Rx-, Tx+, Tx-
Speed 10/100Mbps
Working Full-duplex and half duplex
Working mode Support TCP Server and Client
Transfer distance 100m
Connector RJ45
RS-485/422 port
RS-485 /422 port number 2
RS-485 signal D+, D-, GND
RS-422 signal T+, T-, GND, R+, R-
Parity bit None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit 1bit,1.5bit,2bit
Band rate 300bps115200bps
Loading support 32 nodes loop back
Transfer distance 1200m
Connector terminal block
Protection class 3 static, 1.5KV isolation
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS-485/422 port data indicator TX, RX
Power supply
Input voltage 12VDC(9~48VDC)
No-load consumption0.89W@12VDC
Full-load consumption 0.93W@12VDC
Environment limits
Working temperature -40~85℃
Storage temperature -40~85℃
Relative humidity 5%~95%non-condensing

Approx. Rs 10,300 / Piece Get Latest Price

Model : NP302T-2D(RS-485)NP302T-2D(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 2 port RS-485/422(RS-485/422 connector: 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-485/422 port
RS-485 /422 port number: 2
RS-485 signal: D+, D-, GND
RS-422 signal: T+, T-, GND, R+, R-
Parity bit: None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit: 1bit,1.5bit,2bit
Band rate: 300bps～115200bps
Loading: support 32 nodes loop back
Transfer distance: 1200m
Connector: terminal block
Protection: class 3 static, 1.5KV isolation
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS-485/422 port data indicator: TX, RX
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:0.89W@12VDC
Full-load consumption: 0.93W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell: IP30 protection, metal shell
Installation: Wall mounting
Weight: 238.6g
Size (L×W×H): 100mm×69mm×22mm

Approx. Rs 10,300 / Piece Get Latest Price

Model : NP302T-2D(RS-485)NP302T-2D(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 2 port RS-485/422(RS-485/422 connector: 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 2 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-485/422 port
RS-485 /422 port number: 2
RS-485 signal: D+, D-, GND
RS-422 signal: T+, T-, GND, R+, R-
Parity bit: None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit: 1bit,1.5bit,2bit
Band rate: 300bps～115200bps
Loading: support 32 nodes loop back
Transfer distance: 1200m
Connector: terminal block
Protection: class 3 static, 1.5KV isolation
LED Indicator
Power (PWR)
Ethernet port connect statue (Link)
RS-485/422 port data indicator: TX, RX
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:0.89W@12VDC
Full-load consumption: 0.93W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell: IP30 protection, metal shell
Installation: Wall mounting
Weight: 238.6g
Size (L×W×H): 100mm×69mm×22mm

Approx. Rs 14,000 / Piece Get Latest Price

Model : NP304T-4D(RS-232)NP304T-4D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 4 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 4 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-232 port
RS-232 port number: 4
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR,  RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit: 5bit, 6bit, 7bit, 8bit
Stop bit: 1bit, 1.5bit, 2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 4 static
LED Indicator
Working statue indicator: RUN
Power (PWR)
Ethernet port connection statue (Link)
RS232 port transmit data indicator: TX1~TX4
RS232 port receive data indicator: RX1~RX4
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:1.05W@12VDC
Full-load consumption: 1.16W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell: IP30 protection, metal shell
Installation: Wall mounting
Weight: 460g
Size (L×W×H): 160mm×95.5mm×28mm
Standard
EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A
EMS: EN 55024,
          EN 61000-4-2 (ESD) Level 3,
          EN 61000-4-3 (RS) Level 3,
          EN 61000-4-4 (EFT) Level 4,
          EN 61000-4-5 (Surge) Level 3,
          EN 61000-4-6 (CS) Level 3,
          EN 61000-4-8,
          EN 61000-4-11
Shock: IEC 60068-2-27
Free fall: IEC 60068-2-32
Vibration: IEC 60068-2-6 

Approx. Rs 14,000 / Piece Get Latest Price

Model : NP304T-4D(RS-232)NP304T-4D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 4 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 4 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-232 port
RS-232 port number: 4
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR,  RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit: 5bit, 6bit, 7bit, 8bit
Stop bit: 1bit, 1.5bit, 2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 4 static
LED Indicator
Working statue indicator: RUN
Power (PWR)
Ethernet port connection statue (Link)
RS232 port transmit data indicator: TX1~TX4
RS232 port receive data indicator: RX1~RX4
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:1.05W@12VDC
Full-load consumption: 1.16W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell: IP30 protection, metal shell
Installation: Wall mounting
Weight: 460g
Size (L×W×H): 160mm×95.5mm×28mm

Approx. Rs 13,000 / Piece Get Latest Price

Model : NP304T-4D(RS-232)NP304T-4D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 4 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 4 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-232 port
RS-232 port number: 4
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR,  RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit: 5bit, 6bit, 7bit, 8bit
Stop bit: 1bit, 1.5bit, 2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 4 static
LED Indicator
Working statue indicator: RUN
Power (PWR)
Ethernet port connection statue (Link)
RS232 port transmit data indicator: TX1~TX4
RS232 port receive data indicator: RX1~RX4
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:1.05W@12VDC
Full-load consumption: 1.16W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell: IP30 protection, metal shell
Installation: Wall mounting
Weight: 460g
Size (L×W×H): 160mm×95.5mm×28mm

Approx. Rs 13,000 / Piece Get Latest Price

NP304T-4D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 4 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 4 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-232 port
RS-232 port number: 4
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR,  RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit: 5bit, 6bit, 7bit, 8bit
Stop bit: 1bit, 1.5bit, 2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 4 static
LED Indicator
Working statue indicator: RUN
Power (PWR)
Ethernet port connection statue (Link)
RS232 port transmit data indicator: TX1~TX4
RS232 port receive data indicator: RX1~RX4
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:1.05W@12VDC
Full-load consumption: 1.16W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell: IP30 protection, metal shell
Installation: Wall mounting
Weight: 460g
Size (L×W×H): 160mm×95.5mm×28mm

Approx. Rs 14,300 / Piece Get Latest Price

NP304T-4DI(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 4 port RS-485/422(RS-485/422 connector: 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 4 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
  Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-485/422 port
RS-485/422 port number: 4
RS-422 signal: T+(A), T-(B), R+(A), R-(B)
RS-485 signal: D+(A), D-(B)
Parity bit: None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit: 1bit,1.5bit,2bit
Band rate: 300bps～115200bps
Loading: support 32 nodes loop back
Transfer distance: 1200m
Connector:4-bit terminal block
Protection: class 3 static, 1.5KVAC isolation
LED Indicator
Working statue indicator: RUN
Power (PWR)
Ethernet port connection statue (Link)
RS-485/422 port transmit data indicator: TX1~TX4
RS-485/422 port receive data indicator: RX1~RX4
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:1.35W@12VDC
Full-load consumption: 1.44W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell: IP30 protection, metal shell
Installation: Wall mounting
Weight: 450g
Size (L×W×H): 160mm×95.5mm×28mm

Approx. Rs 14,000 / Piece Get Latest Price

NP304T-4DI(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 4 port RS-485/422(RS-485/422 connector: 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 4 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
  Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-485/422 port
RS-485/422 port number: 4
RS-422 signal: T+(A), T-(B), R+(A), R-(B)
RS-485 signal: D+(A), D-(B)
Parity bit: None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit: 1bit,1.5bit,2bit
Band rate: 300bps～115200bps
Loading: support 32 nodes loop back
Transfer distance: 1200m
Connector:4-bit terminal block
Protection: class 3 static, 1.5KVAC isolation

Approx. Rs 16,500 / Piece Get Latest Price

Model : NP308T-8D(RS-232)NP308T-8D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 8 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.

Features

1.Support 10/100M Ethernet
2.Support 8 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
  Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS232 port
RS232 port number: 8
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR,  RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit: 5bit, 6bit, 7bit, 8bit
Stop bit: 1bit, 1.5bit, 2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 3 static
LED Indicator
Working statue indicator: RUN
Power (PWR)
Ethernet port connection statue (Link)
RS232 port transmit data indicator: TX1~TX8
RS232 port receive data indicator: RX1~RX8
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:1.43W@12VDC
Full-load consumption: 1.98W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell:  IP30 protection, metal shell
Installation: Wall mounting
Weight: 524g
Size (L×W×H): 160mm×95.5mm×28mm

Approx. Rs 14,500 / Piece Get Latest Price

Model : NP308T-8D(RS-232)NP308T-8D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 8 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.
Moreover, NP308T-8D(RS-232) provide strong function configuration tools based in Windows platform, it can guide user configure the device step by step, all configurations are coming true by WEB or Telnet, support cross-gateway and cross-router, user can can flexible configure IP address, server and client mode, data bag size etc.
NP308T-8D(RS-232) adopts EMC protection design, can work in rugged environment.

Features

1.Support 10/100M Ethernet
2.Support 8 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
  Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS232 port
RS232 port number: 8
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR,  RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit: 5bit, 6bit, 7bit, 8bit
Stop bit: 1bit, 1.5bit, 2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 3 static
LED Indicator
Working statue indicator: RUN
Power (PWR)
Ethernet port connection statue (Link)
RS232 port transmit data indicator: TX1~TX8
RS232 port receive data indicator: RX1~RX8
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:1.43W@12VDC
Full-load consumption: 1.98W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell:  IP30 protection, metal shell
Installation: Wall mounting
Weight: 524g
Size (L×W×H): 160mm×95.5mm×28mm

Approx. Rs 14,500 / Piece Get Latest Price

NP308T-8D(RS-232) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 8 port RS232 (RS-232 connector: RJ45) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.
Moreover, NP308T-8D(RS-232) provide strong function configuration tools based in Windows platform, it can guide user configure the device step by step, all configurations are coming true by WEB or Telnet, support cross-gateway and cross-router, user can can flexible configure IP address, server and client mode, data bag size etc.
NP308T-8D(RS-232) adopts EMC protection design, can work in rugged environment.

Features

1.Support 10/100M Ethernet
2.Support 8 Port RS-232
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
  Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS232 port
RS232 port number: 8
RS-232 signal: DCD, RXD, TXD, DTR, GND, DSR,  RTS, CTS
Parity bit: None, Even, Odd, Space, Mark
Data bit: 5bit, 6bit, 7bit, 8bit
Stop bit: 1bit, 1.5bit, 2bit
Band rate: 300bps～115200bps
Loading: point to point
Transfer distance: no more than 15m
Connector: RJ45
Protection: class 3 static
LED Indicator
Working statue indicator: RUN
Power (PWR)
Ethernet port connection statue (Link)
RS232 port transmit data indicator: TX1~TX8
RS232 port receive data indicator: RX1~RX8
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption:1.43W@12VDC
Full-load consumption: 1.98W@12VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell:  IP30 protection, metal shell
Installation: Wall mounting
Weight: 524g
Size (L×W×H): 160mm×95.5mm×28mm

Approx. Rs 15,600 / Piece Get Latest Price

NP308T-8DI(RS-485)NP308T-8DI(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 8 port RS-485/422(RS-485/422 connector 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.
Moreover, NP308T-8DI(RS-485) provide strong function configuration tools based in Windows platform, it can guide user configure the device step by step, all configurations are coming true by WEB or Telnet, support cross-gateway and cross-router, user can can flexible configure IP address, server and client mode, data bag size etc.
NP308T-8DI(RS-485) adopts EMC protection design, can work in rugged environment.

Features

1.Support 10/100M Ethernet
2.Support 8 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature -4085℃

Specification

Ethernet port
Standard 10Base-T, 100Base-TX
Protocol Support TCP, UDP, APR, ICMP and DHCP
Signal Rx+, Rx-, Tx+, Tx-
Speed 10/100Mbps
Working Full-duplex and half duplex
Working mode Support TCP Server and Client
Transfer distance 100m
Connector RJ45
RS-485/422 port
RS-485/422 port number 8
RS-422 signal T+(A), T-(B), R+(A), R-(B)
RS-485 signal D+(A), D-(B)
Parity bit None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit 1bit,1.5bit,2bit
Band rate 300bps115200bps
Loading support 32 nodes loop back
Transfer distance 1200m
Connector4-bit terminal block
Protection class 3 static, 1.5KVAC isolation
LED Indicator
Working statue indicator RUN
Power (PWR)
Ethernet port connection statue (Link)
RS-485/422 port transmit data indicator TX1~TX8
RS-485/422 port receive data indicator RX1~RX8
Power supply
Input voltage 12VDC(9~48VDC)
No-load consumption 1.81W@5VDC
Full-load consumption 2.36W@5VDC
Environment limits
Working temperature -40~85℃
Storage temperature -40~85℃
Relative humidity 5%~95%non-condensing
Mechanical
Shell IP30 protection, metal shell
Installation Wall mounting
Weight 486g
Size (L×W×H) 160mm×95.5mm×28mm
Standard
EMI EN 55022 Class A, FCC Part 15 Subpart B Class A
EMS EN 55024,
EN 61000-4-2 (ESD) Level 3,
EN 61000-4-3 (RS) Level 3,
EN 61000-4-4 (EFT) Level 4,
EN 61000-4-5 (Surge) Level 3,
EN 61000-4-6 (CS) Level 3,
EN 61000-4-8,
EN 61000-4-11
Shock IEC 60068-2-27
Free fall IEC 60068-2-32
Vibration IEC 60068-2-6

Approx. Rs 16,000 / Piece Get Latest Price

Model NP308T-8DI(RS-485)NP308T-8DI(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 8 port RS-485/422(RS-485/422 connector 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.
Moreover, NP308T-8DI(RS-485) provide strong function configuration tools based in Windows platform, it can guide user configure the device step by step, all configurations are coming true by WEB or Telnet, support cross-gateway and cross-router, user can can flexible configure IP address, server and client mode, data bag size etc.
NP308T-8DI(RS-485) adopts EMC protection design, can work in rugged environment.

Features

1.Support 10/100M Ethernet
2.Support 8 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and
Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature -4085℃

Specification

Ethernet port
Standard 10Base-T, 100Base-TX
Protocol Support TCP, UDP, APR, ICMP and DHCP
Signal Rx+, Rx-, Tx+, Tx-
Speed 10/100Mbps
Working Full-duplex and half duplex
Working mode Support TCP Server and Client
Transfer distance 100m
Connector RJ45
RS-485/422 port
RS-485/422 port number 8
RS-422 signal T+(A), T-(B), R+(A), R-(B)
RS-485 signal D+(A), D-(B)
Parity bit None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit 1bit,1.5bit,2bit
Band rate 300bps115200bps
Loading support 32 nodes loop back
Transfer distance 1200m
Connector4-bit terminal block
Protection class 3 static, 1.5KVAC isolation
LED Indicator
Working statue indicator RUN
Power (PWR)
Ethernet port connection statue (Link)
RS-485/422 port transmit data indicator TX1~TX8
RS-485/422 port receive data indicator RX1~RX8
Power supply
Input voltage 12VDC(9~48VDC)
No-load consumption 1.81W@5VDC
Full-load consumption 2.36W@5VDC

Approx. Rs 16,500 / Piece Get Latest Price

Model : NP308T-8DI(RS-485)NP308T-8DI(RS-485) is an high performance, industrial grade serial to Ethernet server, it can satisfy some kinds of customer requirements in consumption, temperature, volume and handle ability. It provides 8 port RS-485/422(RS-485/422 connector: 5 bit terminal block) and 1 port 10/100Base-Tx Ethernet, can focus manage disperse serial device, master through network, easy, convenience. In application, can configure, upgrade through WEB.
Moreover, NP308T-8DI(RS-485) provide strong function configuration tools based in Windows platform, it can guide user configure the device step by step, all configurations are coming true by WEB or Telnet, support cross-gateway and cross-router, user can can flexible configure IP address, server and client mode, data bag size etc.
NP308T-8DI(RS-485) adopts EMC protection design, can work in rugged environment.

Features

1.Support 10/100M Ethernet
2.Support 8 Port RS-485/422
3.Support WEB and Telnet configuration
4.Support TCP, UDP, ARP, ICMP, DHCP and DNS protocol
5.Support TCP Server, TCP Client, TCP Auto, UDP and 
  Real COM driver working mode
6.Support UDP multicast and UDP subnet mode
7.Support heartbeat time and time over disconnect function
8.Support cross-gateway and cross-router communication    
9.Support virtual serial COM port access and Network interruption automatic recovery
10.Provide Windows configuration tools for easy to use, easy to bath install.
11.Industrial grade design, IP30 protection grade
12.No fan, low consumption design
13.Working temperature: -40～85℃

 Specification

Ethernet port
Standard: 10Base-T, 100Base-TX
Protocol: Support TCP, UDP, APR, ICMP and DHCP
Signal: Rx+, Rx-, Tx+, Tx-
Speed: 10/100Mbps
Working: Full-duplex and half duplex
Working mode: Support TCP Server and Client
Transfer distance: 100m
Connector: RJ45
RS-485/422 port
RS-485/422 port number: 8
RS-422 signal: T+(A), T-(B), R+(A), R-(B)
RS-485 signal: D+(A), D-(B)
Parity bit: None, Even, Odd, Space, Mark
Data bit; 5bit,6bit,7bit,8bit
Stop bit: 1bit,1.5bit,2bit
Band rate: 300bps～115200bps
Loading: support 32 nodes loop back
Transfer distance: 1200m
Connector:4-bit terminal block
Protection: class 3 static, 1.5KVAC isolation
LED Indicator
Working statue indicator: RUN
Power (PWR)
Ethernet port connection statue (Link)
RS-485/422 port transmit data indicator: TX1~TX8
RS-485/422 port receive data indicator: RX1~RX8
Power supply
Input voltage: 12VDC(9~48VDC)
No-load consumption: 1.81W@5VDC
Full-load consumption: 2.36W@5VDC
Environment limits
Working temperature: -40~85℃
Storage temperature: -40~85℃
Relative humidity: 5%~95%（non-condensing）
Mechanical
Shell:  IP30 protection, metal shell
Installation: Wall mounting
Weight: 486g
Size (L×W×H): 160mm×95.5mm×28mm

Approx. Rs 9,100 / Piece Get Latest Price

The KI-N135 is a ultra compact 1U chassis with the storage, cooling and functionality of larger cases,4*4 cm fans blow the motherboard from side directly to provide the best cooling system.

The KI-N135 has two 3.5" hard drive bays internally